loulou you are not getting old its just your body needs more work lol

loulou i think what cobra has shown it good idea with grub screw in metal hex just need bigger size much better than bonding hex

.. NAT .. 11 mm ...

NAT .. the idea of COBRA98 is excellent .. but to make stronger these rims (for the slow crawleeng) .. can be placed twice in the rim, the rim would be higher .. that you think ?

thanks loulou i was unsure i to am getting old...

quote:

Originally posted by loulou:
NAT .. the idea of COBRA98 is excellent .. but to make stronger these rims (for the slow crawleeng) .. can be placed twice in the rim, the rim would be higher .. that you think ?

yes loulou twice in the rimm is better idea much stronger

do you still have the drawering of this loulou

Changes may occur at any time :-)




############################################
PS .............

NAT .. you are too young to be sitting with these brave people ..

thanks loulou but i feel the days are getting longer .

.. HELLO ..
I enlarged the center hex (11 mm) and they fit very well on the shaft ..



It remains for me to a small hole drilled in the centre of the hex and also on the shaft .. and inserted a rod (pin) to firmly attached, hex ..



Those on the front, should be cut somewhat ..



And then, I must prepared rims, the way that we demonstrate NAT, so the rim fits on the hex set firmly on the shaft ..



There will be (1) hex at the front wheel ..




And maybe (2) at the back (for the slow-crawling, the rear wheels must be very strong) ..



I must buy small-drill bits and some washers, of different sizes ..

Hexes of plastic, which became the center expanded, over time, up to the past .. I hope ..

I shall return later, with a few other pics this mod ..
.. THANK

PS .. The change can occur during the installation of these hex metal ..

This message has been edited. Last edited by: loulou,

Good job Loulou,Between you and NAT,The two of you have come up with a good fix for the 1/6 hex problem

THANK .. COBRA98 ..

(((( unity is strength )))) :-)

##############################################

The problem of these hex plastic resolved, we will be able to review the gearing of JEEP 1/6, to make a real crawler ..

I would have liked to do it on my LAND ROVER, but I decided to keep the stock at 80% ..

So, it will slow down significantly JEEP 1/6, and give it more strength .. improved flex max .. installed FLAPDING / SEAND shock .. installing more efficient motors .. Building a ((cabin)).. installed roll bar .. installation of an antenna metal .. installation of track-bar .. installation of rock-slider .. find ? softer tires .. etc ..

Labour prespective .. but the pleasure is always there ..

This message has been edited. Last edited by: loulou,

good work loulou you have done well .i know what you mean about the small drill bits i have snap d a few .it is important that time is taken when drilling the hex and the drive shaft . mistakes can be made .so take your time . also would like to thank cobra98 for his input on this .

NAT .. these small hole in the shaft, should be well drilled .. I will be very attention ..

YES ..
THANK .. MR COBRA98 :-) for his good advice and his attendance in this forum ..

.. and also MR NOT A TOY (NAT) :-)

HELLO ..

I drilled a small hole in the hex .. it remains to be drilled, four shaft ..

I will pull them out of the diff, to be sure to do a good job ..

Then, a small metal pin will be inserted into these holes to secure the whole ..

The rear shaft, will have two hex, so these wheels are stronger .. Inside the rear wheels should be reworked to accept these two hexes ( if the work can be done ? ) .. THANK ..

great work loulou as always what size drill bit is that loulou mm plz iam from the modern age .lol.

HELLO .. NAT ..

Nothing is stopped .. everything continues .. This LAND ROVER will be as I want :-)


5/64 is the size of the drill ..

..

thanks loulou i think that converts to 00,2 mm if my brain is working .

ahhh see iam not so old after all lol still ok at my math .lol